Automatic Gate Repair in Plano and Frisco
An electric gate that misbehaves almost always has one small culprit hiding in a bigger system. We work through that system in order and fix the piece that actually failed.
Open 24 hours, 7 days a week

Symptoms to watch for
It starts, then backs up
A gate that reverses a few feet into its travel is often reacting to a blocked photo eye, a loose edge sensor or a force setting that no longer matches the gate.
Nothing happens at all
No click, no hum, no lights on the board. Suspect the supply first: breaker, fuse, battery or the feed wire itself.
Works from inside, not outside
If the exit side works but the remote or keypad does not, the motor is probably fine and the trouble sits with the opening device or its receiver.
Runs slow or stops short
Low battery voltage, a binding hinge or a dragging wheel can make the operator labor and quit before the gate reaches its limit.
Where we start on every automatic gate
Before touching the electronics, we release the operator and move the gate by hand. A gate that swings or rolls smoothly on its own tells us the problem is electrical or a setting. A gate that drags, sticks or sags tells us the operator has been fighting the hardware, and replacing a motor would only hide that for a while.
From there we check incoming power, then the control board, then each input in turn: the safety devices, the opening devices and the limit settings. Working in that order keeps us from swapping parts that were never broken, which keeps the visit shorter and the bill tied to the real fault.
What we see on gates around Plano and Frisco
Most of the automatic gates we work on here belong to newer homes in master-planned neighborhoods, office parks along the Dallas North Tollway and the SH 121 corridor, and community entrances that cycle all day. Many of them use contemporary horizontal-slat or flat steel panels, which catch more wind than a traditional picket gate and put extra load on hinges and operator arms.
Weather plays a part too. The highest temperature ever recorded at DFW Airport is 113 degrees, reached in June 1980, and long summer stretches cook the batteries and boards that sit inside sealed operator housings. Spring storms bring hail and lightning, and a surge on the line can quietly damage a board that looks fine from the outside.
Typical fixes
Every gate is different, but most repairs land in one of these groups:
- Cleaning and re-aiming photo eyes, or replacing a sensor that has failed
- Replacing a tired backup battery or a charger that no longer holds voltage
- Resetting open and close limits after a power loss or board change
- Replacing a damaged control board, fuse or surge part
- Fixing the hinge, roller or track problem that was overworking the operator
- Reprogramming remotes and keypads after a reset
Pricing and what changes it
We do not post prices because the honest answer depends on what we find. The operator model, whether a part is in stock locally, how far the gate is from power and whether more than one thing failed all change the number. Call for pricing on your gate and ask about current discounts when you call. We explain the repair and the cost before the work starts.
Quick checks you can do safely
- Look at the breaker or outlet that feeds the gate and reset it once if it tripped.
- Wipe both photo eye lenses and make sure nothing sits between them.
- Test with another opener, such as a spare remote or the keypad, to narrow it down.
- Note any lights or beeps on the operator so you can describe them on the call.
Keep everyone clear
If the gate is acting strangely, give it a wide berth and keep kids, pets and vehicles back. Never wire around a sensor to make the gate close. If it will not stop, cut power at the breaker and call.
Common questions
Can you repair the gate without replacing the whole operator?
Usually, yes. Most failures come down to a battery, sensor, board input or hardware problem. We only suggest a new operator when the old one cannot be repaired sensibly, and we explain why.
Why does my gate open fine but refuse to close?
Closing is where the safety devices take control. A dirty or misaligned photo eye, a stuck edge sensor or an exit loop that thinks a car is present will all hold a gate open.
Do you work on both swing and sliding automatic gates?
Yes. We repair powered swing gates, slide gates and their operators at homes, businesses and neighborhood entrances.
How do I get a price?
Call (469) 393-4388 and describe what the gate is doing. Call for pricing on your gate, and ask about current discounts when you call.
You may also need
- Gate Opener RepairMotors, gearboxes, boards and batteries inside swing arm and slide gate operators.
- Stuck Gate RepairGates stuck open or shut, stalling halfway, reversing, slow, loud or off track.
- Safety Sensor & Loop RepairPhoto eyes, safety edges, exit and safety loops, and loop detectors on automatic gates.
Automatic Gate Repair in Plano, Frisco and nearby
Open 24 hours, 7 days a week. Call for pricing. Ask about current discounts when you call.