Skip to content
CollinGate Repair · 24/7

Gate Electrical and Wiring Repair in Plano, Frisco and Richardson

Follow the electricity from the breaker to the opener and on to every sensor, and somewhere along that path the fault is waiting. Most gate electrical problems are low-voltage issues we can trace and repair. New line-voltage circuits go to a licensed electrician.

Open 24 hours, 7 days a week

Gloved hands adjusting a swing gate opener arm mounted on a stone column

Symptoms to watch for

Tracing the power path

We work from the source outward. First the circuit and any GFCI outlet, then the transformer or power supply, then the feed to the board, and finally the low-voltage runs to the photo eyes, loop detector, receiver and second operator. Measuring at each point shows exactly where power drops away.

That method avoids replacing a board or opener that was never the problem. It also turns up the second fault that often hides behind the first, such as a corroded splice next to the wire that was cut.

Underground wiring and low-voltage control wiring

In Plano and Frisco yards, gate cables usually run underground through landscaped beds, under sidewalks and across the driveway. Expansive clay, root growth and later digging all work against them. Conduit that has separated at a joint lets water in, and direct-buried wire is easily nicked by a shovel.

We repair at an accessible point where we can, or pull new wire through existing conduit. Where the conduit is gone or crushed, a new run may need trenching or a saw cut across concrete, and we explain the route before any digging.

Transformers, chargers, relays and junction boxes

Wiring jobs we regularly handle include:

  • Transformer and power supply replacement
  • Battery charger testing and replacement
  • Relay, contactor and fuse repair
  • Junction box, enclosure and terminal block replacement
  • Repairing chewed, corroded or loose connections
  • Surge protection and grounding checks

Surge, lightning and water damage

Spring storms across Collin County regularly bring lightning close to homes. A surge can arrive on the power line or be picked up by long control wires, and it often damages more than one part. Water damage is slower: it creeps into a control box mounted low on a column or into conduit with an open end, then corrodes terminals over weeks.

We replace only what testing shows is damaged, then deal with the cause by sealing entries, adding drip loops or moving equipment higher.

Solar-to-AC conversion and line-voltage work

A solar gate shaded by mature trees may never charge fully, and an AC gate at a far corner of an acreage lot in Parker may be easier to run on solar. We handle either conversion on the gate side.

We are not electricians and do not work on line-voltage circuits. If the gate needs a new circuit, outlet or breaker, a licensed electrician does that part. We can tell them exactly what the opener requires.

Pricing and what changes it

The price depends on where the fault sits, how much wire is replaced, whether trenching or saw cutting is required, and which parts were damaged. Call for pricing, and ask about current discounts.

Quick checks you can do safely

  • Reset the breaker and any GFCI outlet that feeds the gate
  • Look for lights on the board, charger and any wireless accessories
  • Think about recent digging, irrigation or landscaping near the gate
  • Check where wires leave the ground for cuts or chewed insulation
  • Keep the control box shut if it is wet inside or smells burnt

Keep everyone clear

Line voltage at a gate can cause serious injury, especially near wet ground and metal. Turn the breaker off before opening the control box, and do not touch a box that shows scorching or water. Any household wiring or new circuit is work for a licensed electrician.

Common questions

Why does only one side of my double gate work?

The cable linking the two operators has probably failed, or the second operator has lost power or a connection. Both are tested on site.

Can a cut wire under my driveway be repaired?

Often. If the wire is in conduit, new wire can usually be pulled through. If not, a new route may need a trench or saw cut.

Will you run a new electrical circuit to my gate?

No. A licensed electrician handles new line-voltage circuits. We handle the gate side and all low-voltage wiring.

My gate stopped after a thunderstorm. Is the board fried?

Possibly, but a fuse, the receiver or the transformer may be all that failed. We test before replacing anything.

What does gate wiring repair cost?

It depends on the fault, the wire involved and any digging. Call (469) 393-4388 for pricing and ask about current discounts.

You may also need

Gate Wiring Repair in Plano, Frisco and nearby

Open 24 hours, 7 days a week. Call for pricing. Ask about current discounts when you call.

Call nowRequest service