Skip to content
CollinGate Repair · 24/7

Fixing Photo Eyes, Safety Edges and Vehicle Loops

Safety sensors and vehicle loops decide when an automatic gate is allowed to move. When one of them fails or gets confused, the gate reverses, stays open or opens for no one. We test each device and repair the one giving the operator bad information.

Open 24 hours, 7 days a week

Technician wiping a safety sensor beside a gray sliding driveway gate

Symptoms to watch for

Photo eye repair and alignment

Photo eyes send an infrared beam across the gate path. If something breaks the beam while the gate is closing, the operator stops or reverses. The lenses face the weather every day, and around Plano and Frisco that means dust, spring pollen, sprinkler overspray, spider webs and low afternoon sun shining straight into the receiver. A sensor can also be knocked out of line by a mower, a trash bin or a car door.

We clean, realign and test photo eyes, trace their wiring back to the operator and replace sensors that have failed. Where a gate has only one pair of eyes, we can talk through adding coverage on the other side of the gate path to reduce the risk of entrapment.

  • Photo-eye installation, replacement and alignment
  • Photo-eye troubleshooting for gates that reverse or will not close
  • Through-beam and reflective infrared sensor replacement

Safety edge and obstruction sensor repair

A safety edge is a pressure-sensitive strip on the leading edge of a gate or along a post. When it is pressed, it tells the operator to stop and reverse. Edges split, take hits from cars and dry out in the sun. Wired edges can lose their connection at a coiled cord or cracked connector, and wireless safety edges depend on a small transmitter battery that eventually runs down.

We test each edge, replace damaged ones and repair the wiring or wireless transmitter behind them. Obstruction sensing built into the operator itself is checked and adjusted at the same time.

  • Safety edge installation and replacement
  • Wireless safety edge repair and transmitter battery replacement
  • Entrapment and obstruction sensor repair
  • Entrapment protection upgrades on older gates

Vehicle loop and loop detector repair

A vehicle loop is a coil of wire laid in a narrow saw cut in the driveway or buried beneath it. A loop detector, usually inside the operator housing, senses the metal of a car over the loop. A free-exit loop opens the gate for cars leaving. A safety loop, called a shadow loop when it sits under the swing path of a gate, keeps the gate from closing on or swinging into a car that is in the way.

Loops fail in predictable ways. Clay soil movement cracks driveway slabs and pulls loop wire apart. Pavement repair, resurfacing and new concrete cut through loops no one marked. Old sealant pops out and lets water reach the wire. A detector can also drift or lose its settings after a surge, so it misses cars or sees cars that are not there.

We test the loop wire and the detector separately so we know which one failed. Repairs range from adjusting and reprogramming the loop detector, to resealing an exposed loop, to saw cutting and installing a new underground exit loop or safety loop.

  • Free-exit loop and safety loop repair and replacement
  • Underground exit loop installation and loop saw cutting
  • Loop detector replacement and programming
  • Above-ground vehicle detectors and magnetic vehicle sensors where cutting the drive is not practical

Gate safety inspection for homes and HOA entrances

Automatic gates should stop and reverse when something is in their path, and there are published industry standards, such as UL 325 and ASTM F2200, for how gates and their safety devices should be set up. We do not certify gates. When we work on one, we check that the photo eyes, edges and loops work the way those standards expect, that warning signs are posted where people can see them, and that the force setting is not so high that the gate pushes through an obstruction.

Community entrances and gates beside sidewalks see walkers, bikes and kids, so these checks matter even more there. If we find a gap in protection, we explain it and give you options.

What changes the price

Sensor and loop repairs vary. Cleaning and realigning a photo eye is a small job, while cutting a new loop into a driveway takes more time and material. The number of devices, the operator model and the condition of the concrete all change the price. Call for pricing on your gate and ask about current discounts when you call.

Quick checks you can do safely

  • Wipe both photo-eye lenses with a soft cloth and look for an indicator light on each sensor.
  • Make sure plants, decorations or trash bins are not sitting in the beam path.
  • Look along the safety edge for splits, missing sections or a dangling cord.
  • Check the driveway near the gate for new cracks, patches or cut lines.
  • Note whether the problem shows up in rain, at a certain time of day or only with certain vehicles.

Keep everyone clear

Never jumper or bypass a sensor to make a gate close. Those devices are what keep the gate from striking a person, pet or car. If the gate is closing on things or moving on its own, turn off its power and leave it open safely until it is repaired.

Common questions

Why does my gate start to close and then reverse?

Most often a photo eye is blocked, dirty or misaligned, or a safety edge reads as pressed. A force setting that no longer matches the gate can also cause it. We test each input to find the one at fault.

Why does my gate open by itself?

A falsely triggered exit loop or loop detector is a common cause, especially after driveway cracks, concrete work or heavy rain. A stuck input or a remote pressed in a parked car can do it too.

Can you add a loop to a driveway that has none?

Yes. We can saw cut and install exit or safety loops in concrete or asphalt and connect a detector to the operator. Where cutting is not practical, an above-ground detector may work instead.

Do my gate sensors meet UL 325?

We do not certify gates, but we check that your photo eyes, edges and loops work the way the safety standards for automatic gates expect, and we tell you if something is missing.

How much does safety sensor or loop repair cost?

It depends on which device failed and whether new loop wire has to be cut in. Call (469) 393-4388 for pricing and ask about current discounts.

You may also need

Safety Sensor & Loop Repair in Plano, Frisco and nearby

Open 24 hours, 7 days a week. Call for pricing. Ask about current discounts when you call.

Call nowRequest service