Sliding Gate Repair in Plano and Frisco, TX
Slide gates are simple machines with a lot of weight on a few small parts. When one roller, guide or rack section wears out, the whole gate starts to fight its operator.
Open 24 hours, 7 days a week

Symptoms to watch for
Jumped off the track
A gate that has left its track can tip or fall. Leave it where it is and call; forcing it back usually bends the frame.
Loud grinding or squeal
Worn wheel bearings, a flat-spotted roller or a rack tooth that has lost contact with the drive gear all make noise before they fail.
Stops at the same spot
A gate that halts at one point every cycle is often catching on a bent track section, debris or a loose guide.
Rattles or wobbles at the top
Loose or missing top guide rollers let the gate lean, which wears the bottom wheels and can pull the rack away from the gear.
Track-riding and cantilever gates
Most residential slide gates ride on V-groove wheels sitting on an inverted angle track set in the concrete. The track has to stay clean and straight. Gravel, mulch and small dents are enough to make the wheels climb out of the groove.
Cantilever gates, common at office parks and storage yards, do not touch the ground. They hang on roller trucks mounted to posts beside the opening. Those trucks carry the entire weight of the gate, so their bearings and the alignment of the posts matter more than anything else.
Rack, chain and drive gear
The operator moves the gate through a toothed rack or a chain. If the rack sags or a section comes loose, the gear skips and the gate jerks or stops. Chains stretch and need tension adjusted. We realign the rack along its full length so the gear meets it evenly from end to end.
Why concrete and slab movement matter here
Driveways shift over time in North Texas as soil dries and swells with the seasons. On a slide gate, a small change in slab height can tilt the track enough to put pressure on one wheel or pinch the gate at the end of its travel. When we find that, we adjust the track and guides instead of only replacing the worn wheel.
Safety on sliding gates
A rolling gate can trap a hand or foot at the post and along the rack. Proper gate guards, photo eyes and edge sensors reduce that risk. We check that the safety devices stop and reverse the gate before we call the job done.
- Photo eyes across the opening in both directions
- Contact edges on the leading and trailing ends
- Guarding over the gap where the gate passes the post
Quick checks you can do safely
- Clear the track of rocks, mulch and leaves along its full length.
- Look for a wheel that has climbed out of the V-groove, and do not try to lift it back yourself.
- Check that the top guide rollers are present and the gate is not leaning.
- Listen for where in the travel the noise starts.
Keep everyone clear
Slide gates are heavy and can fall if they leave the track or lose a guide. Keep everyone away from a gate that is leaning or off its wheels and call before moving it.
Common questions
My sliding gate came off the track. Can I put it back on?
We advise against it. A gate off its track is unstable, and lifting it back usually means working against hundreds of pounds without proper support. Call (469) 393-4388.
Why is my sliding gate so loud?
Noise usually comes from worn roller bearings, a damaged wheel or the rack riding unevenly on the drive gear. Catching it early is cheaper than waiting for a part to break.
Do you repair cantilever gates at businesses?
Yes. We service roller trucks, guide posts, racks and operators on cantilever and track-riding slide gates.
What does a sliding gate repair cost?
It depends on which parts are worn and the size of the gate. Call for pricing on your gate and ask about current discounts.
You may also need
- Automatic Gate RepairDiagnosis and repair for powered swing and slide gates that stall, reverse or refuse to move.
- Commercial Gate RepairSlide, cantilever and swing gates at offices, warehouses, storage lots and apartment drives.
- Gate Welding & Frame RepairWelding, straightening and rebuilding for steel, iron and aluminum gate frames, brackets and pickets.
Sliding Gate Repair in Plano, Frisco and nearby
Open 24 hours, 7 days a week. Call for pricing. Ask about current discounts when you call.